View EL7412_449505.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
EL7412
Data Sheet August 26, 2004, Rev B FN7287.1
High Speed, Four Channel Power MOSFET Drivers
The EL7412 contains (4) high performance matched drivers. These very high speed drivers are capable of delivering peak currents of 2.0 amps into highly capacitive loads and are ideally suited for "Full bridge' and ultrasound applications. The high speed performance is achieved by means of a proprietary "Turbo-Driver' circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. The matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with nonoverlapped drive techniques.
Features
* Excellent response times * Matched rise and fall times * Reduced clock skew * Low output impedance * Low input capacitance * High noise immunity * Improved clocking rate * Low supply current * Wide operating voltage range * Pb-free available
Applications
* Full bridge drivers * Clock/line drivers * CCD Drivers
Pinout
EL7412 [20-PIN SO (0.300")] TOP VIEW
* Ultra-sound transducer drivers * Power MOSFET drivers * Switch mode power supplies * Class D switching amplifiers * Ultrasonic and RF generators * Pulsed circuits
Ordering Information
PART NUMBER
Note 1: Pins 4-7 and 14-17 are electrically connected.
PACKAGE 20-Pin SO (0.300") 20-Pin SO (0.300") 20-Pin SO (0.300") (Pb-free) 20-Pin SO (0.300") (Pb-free)
TAPE & REEL 13" 13"
PKG. DWG. # MDP0027 MDP0027 MDP0027 MDP0027
EL7412CM EL7412CM-T13
Manufactured under U.S. Patent Nos. 5,334,883, #5,331,047 EL7412CMZ (See Note) EL7412CMZT13 (See Note)
NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which is compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J-Std-020C.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Elantec Semiconductor, Inc. 1996, Intersil Americas Inc. 2004. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc. All other trademarks mentioned are the property of their respective owners.
1
EL7412
Absolute Maximum Ratings (TA = 25C)
Supply (V+ to Gnd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V above V+ Combined Peak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . .8A Storage Temperature Range . . . . . . . . . . . . . . . . . .-65C to +150C Ambient Operating Temperature . . . . . . . . . . . . . . . .-40C to +85C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
DC Electrical Specifications
PARAMETER INPUT VIH IIH VIL IIL VHVS OUTPUT ROH ROL IPK IDC POWER SUPPLY IS VS Pull-Up Resistance
TA = 25C, VDD = 15V unless otherwise specified TEST CONDITIONS MIN TYP MAX UNITS
DESCRIPTION
Logic "1' Input Voltage Logic "1' Input Current Logic "0' Input Voltage Logic "0' Input Current Input Hysteresis @0V @VDD
2.4 0.1 10 0.8 0.1 0.3 10
V A V A V
IOUT = -100mA IOUT = +100mA Source Sink Source/Sink 100
3 4 2 2
6 6
A mA
Pull-Down Resistance Peak Output Current Continuous Output Current
Power Supply Current Operating Voltage
Inputs High 4.5
2
5 15
mA V
AC Electrical Specifications
PARAMETER
TA = 25C, V = 15V unless otherwise specified TEST CONDITIONS MIN TYP MAX UNITS
DESCRIPTION
SWITCHING CHARACTERISTICS tR tF tD1 tD2 Rise Time Fall Time Turn-On Delay Time Turn-Off Delay Time CL = 500pF CL = 1000pF CL = 500pF CL = 1000pF See Timing Table See Timing Table 7.5 10 10 13 18 20 ns 20 20 25 25 ns ns ns
2
EL7412
Timing Table
Standard Test Configuration
Simplified Schematic
3
EL7412 Typical Performance Curves
Max Power/Derating Curves Switch Threshold vs Supply Voltage
Ambient Temperature (C)
Peak Drive vs Supply Voltage Input Current vs Voltage
"ON' Resistance vs Supply Voltage
4
EL7412 Typical Performance Curves
(Continued)
Average Supply Current vs Voltage and Frequency
Average Supply Current vs Capacitive Load
Rise/Fall Time vs Load
Rise/Fall Time vs Supply Voltage
5
EL7412 Typical Performance Curves
(Continued)
Propagation Delay vs Supply Voltage
Rise/Fall Time vs Temperature
Delay vs Temperature
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 6

▲Up To Search▲

Price & Availability of EL7412

	To Download EL7412 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .